# How do you calculate the heat transfer coefficient of a heat exchanger?

## How do you calculate the heat transfer coefficient of a heat exchanger?

Composition

1. = the overall heat transfer coefficient (W/(m2•K))
2. = the contact area for each fluid side (m2) (with and expressing either surface)
3. = the thermal conductivity of the material (W/(m·K))
4. = the individual convection heat transfer coefficient for each fluid (W/(m2•K))
5. = the wall thickness (m).

## How do you calculate the heat transfer coefficient of radiation?

The rate of heat transfer by emitted radiation is determined by the Stefan-Boltzmann law of radiation: Qt=σeAT4 Q t = σ e A T 4 , where σ = 5.67 × 10−8 J/s · m2 · K4 is the Stefan-Boltzmann constant, A is the surface area of the object, and T is its absolute temperature in kelvin.

## What is R value and K-value?

When looking for a material to insulate your building you would generally look for a material with a high R-value, and therefore, one that can resist heat transfer well. While K-value deals solely with just the material, R-value refers to the material and its thickness.

## What is a good R-value?

Depending on where you live and the part of your home you’re insulating (walls, crawlspace, attic, etc.), you’ll need a different R-Value. Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces.

## Is a higher K-value better?

The better insulated a system, the lower its U-value. The greater the performance of a piece of insulation, the greater its R-value and the lower its C-value. The lower the K-value of a particular insulation material, the greater its insulating value for a particular thickness and given set of conditions.

## Which type of insulation has the highest R-value?

Open-cell spray foam is rated at about R-3.5 per inch while closed-cell spray foam is much more efficient at R-6.0 to R-6.5 per inch. Consider spray foam anywhere you need an air barrier as well as insulation.

## What material has the best R-value?

Vacuum insulated panels have the highest R-value, approximately R-45 (in U.S. units) per inch; aerogel has the next highest R-value (about R-10 to R-30 per inch), followed by polyurethane (PUR) and phenolic foam insulations with R-7 per inch.

## What type of insulation has the lowest R-value?

Comparative Insulation R-Values

Insulation Type: R-Value per Inch:
Fiberglass (batts) 2.9 – 3.8
Cellulose (loose) 3.1 – 3.8
Stone Wool (loose) 2.2 – 3.3
Stone Wool (batts) 3.3 – 4.2

## What’s the best type of insulation?

The best types of home attic insulation are open cell spray foam, fiberglass, and cellulose.

• Cellulose is the oldest insulation material used for not only the attic but other areas of the home as well.
• Fiberglass is another traditional insulation material that consists of extremely fine glass fibers.

## Is it better to insulate inside or outside?

Interior insulation is cost effective, but can reduce usable space and doesn’t protect against water. Exterior insulation is expensive and susceptible to insects. Regardless of the insulation choice, efficiency, toxicity and resiliency must all be taken into account as well.

## Is foam board insulation better than fiberglass?

Rigid foam stands up to moisture better than fiberglass. Radiant Heat Floors: Rigid foam is used as a thermal barrier underneath radiant floor heating systems. Rim Joists: Rim joists around the edge of a foundation can be insulated with rigid foam blocks cut to fill the space and caulked in place.

## Does foam board insulation need a vapor barrier?

In houses with spray foam insulation, however, vapor barriers are not necessary. Quality closed cell foam insulation acts as a vapor barrier and does not absorb moisture; at the same time, the insulation prevents leakage by closing air gaps.

## What is the R-value of 1 inch foam board?

3.6 to 4.2 per inch

## What is the difference between pink and blue foam board?

Both are manufactured using the same process and contain similar chemical components. The two products also have the same insulating power. However, blue foam boards are manufactured by Dow Chemical Co. whereas the pink foam boards are manufactured by Owens Corning company.

## What is the R-value of 1/2 foam board?

5.0 per inch

Begin typing your search term above and press enter to search. Press ESC to cancel.